Previously, if the shading device profile was set to 'None' it would be set as 'off continuously' on re-entry. Shading device profile setting retained : The shading device percentile profile group value will be retained on re-entry to the Construction Database. Displayed EN410 g-value updated when glazing properties are edited : When changing the transmittance of the glass the EN 140 g-value will be updated correctly and will match the value in the derived parameters dialog. This will prevent duplicate constructions being reported for the model variants for example in the ASHRAE 90.1 AppG PRM Reports. Profiles use correct references to weather variables : References to the weather variables outside RH, outside moisture content and outside wetbulb temp are correctly used in formula profiles.Ĭonstructions Prevent over counting of constructions in use : When reporting constructions in use only one model variant will be used. IES VE 2012 Feature Pack 01 Release Notes ApPro Assigned daily profile type uneditable after importing weekly profiles : After importing a weekly profile, the type (modulating or absolute) of any existing daily profiles is only editable if they are not referenced by any weekly profile. Tabular Room Data: Crash prevented when adjusting % Saturation values : A problem could occur when the template value for the setting would cause an invalid value to be applied (based on the value of the opposing setting). Tabular Room Data: Error message when changing Thermal Template no longer displayed : Changing thermal template via Tabular Room Data without having first went into VE Compliance will no longer result in an error about the BL2 file not being found.
In the key-in box type “fix=x” to set the precision.Īpache View Adjacency Temperature Profile input character limit updated : The Adjacency temperature profile dropdown has been updated to allow profiles with names greater than 60 characters. Fix key-in precision updated : You can use the “Fix” key-in to set precision to 3, 4, 5 or 6 decimal places. Stay in Component mode after finalizing component : After finalizing a component it will remain in component view rather than returning to the model level. "Fit view" accounts for components outside the zone : The "Fit view" option takes any components into account when scaling to the zone. Trim can only be used on zones that intersect : The trim function can now only be performed on zones that intersect each other.
ModelIT status grid improved for different font and DPI settings : The ModelIT status grid dialog bars will be sized to allow the grid text to be visible for a range of font sizes and DPI settings. The area to be subtracted must bounded the zone. Subtract function updated : Trying to subtract an invalid zone will show an error message. ModelIT Tidy key-in updates : The Tidy key-in can no longer be used on composite spaces. Tabular Room Data and BTM are refreshed following ApPro edits : Tabular Room Data and Tabular Building Template Manager will both be refreshed to reflect any changes that are made in ApPro.
Report "Save as Text" only saves relevant text : When saving a report as a text file the XML data is no longer written out. IES VE 2012 Feature Pack 01 Release Notes VE 2012 Feature Pack 01 Changes General Creating a new project will delete any existing files with the same name : If you create a new project with the same name as an existing project, any existing files will be deleted prior to the creation of the new files so the existing project is completely overwritten. Power factor and control correction factor no longer applied to reported results. Section 6 Notional Building auxiliary energy calculation improved : Revisions made to the Section 6 auxiliary energy calculations for the Notional Building under certain Actual Building scenarios. IES VE 2012 Feature Pack 01 Hotfix 01 Release Notes VE 2012 Feature Pack 01 Hotfix 01 Changes VE Compliance Section 6 SunCast shading file validation check updated : When performing a Section 6 Compliance simulation with the SunCast link on, the validation check has been updated to check for the Notional Building shading file with the naming convention _NS6.shd. Virtual Environment 2012 Feature Pack 01 Hotfix 01 Release Notes IES VE 2012 Feature Pack 01 Hotfix 01 Release Notes VE 2012 Feature Pack 01 Hotfix 01 Changes. Integrated Environmental Solutions Limited Developers of the IES Virtual Environment September 2012 IES Virtual Environment 2012 Feature Pack 01 Hotfix 01 Release Notes
0 kommentar(er)
